Thursday, 24 June 2010

396ci Holden test results in... Our original 396ci Holden short block was recently fitted with our latest design 2010 alloy heads. As noted previously these heads received all new ports, LS1 style rocker system and 8mm valves along with an all new design combustion chamber and a 10 degree valve angle. Existing extractors will bolt straight on along with currently available intake manifolds designed for the conventional VN EFI style heads. Due to port height the intakes require end seal spacers as can be seen in the photo above. Our test engine was fitted with the same CSBS-665 solid lifter flat tappet camshaft (266 intake/270 exhaust duration @ .050"). The stock 1.7:1 LS1 rocker ratio is employed yeilding .630" net valve lift on both intake and exhaust. Compression ratio is 12:1 and pump fuel is no problem with the redesigned chambers. Peak power is 651 bhp @ 6750 rpm and 525 ft.lbs torque @ 5500 rpm These figures are "in the room" figures and no test conditions were changed except for the addition of a set of "GONZO'S" Tri-Y extractors. The same new design COME (low rise) single 4 barrel intake manifold was employed with a 1" open hole spacer although without spacer the difference in power was very marginal. We still have a number of tests and changes we wish to make to the design relating to water jacket location and other valve train updates before finalising the design. Most importantly we now have the most powerful heads for the racing or street/strip Holden V8 engine enabling the old "plastic" to easily compete with any current engines on the market in power per cubic inch stakes. In fact with 1.64 hp per ci this engine easily overshadows most others on pump fuel anywhere...normally aspirated of course and even more relevant, with flat tappet and not roller camshaft. These latest 2010 heads will accept our current design valve covers and we envisage supplying them in bare form for racers who want to do their own but most likely as turn key completely assembled heads with valves, springs, roller rocker setup, valve covers and probably intake manifold. Either our 4 barrel or EFI Twin Throttle Body intake will bolt on with our supplied end seal spacers as part of the conversion kit. Pricing will not be finalised for several months. Exciting times for the Holden V8 are still here. Keep in mind of course our traditional 2009 heads are still the best value for money instant power makers on any Holden V8 engine for street/strip use on ALL capacity Holden V8's. Our latest CNC ported versions complete for $4500.00 will make big power numbers at a bargain price. PACKAGE DEALS CONTINUE... 355ci forged piston balanced stroker kits only...through to July special $2300.00 delivered in Australia. 383ci forged piston balanced stroker kits only...through to July special $2600.00 delivered in Australia. 396ci forged piston balanced stroker kits only...through to July special $3000.00 delivered in Australia. 355ci forged piston stroker kit, "I" beam 4340 steel con rods, nodular cast crank fully balanced, New COME 4 barrel intake...$3000.00 355ci forged piston stroker kit, COME 4 barrel intake, COME 2009 complete alloy heads (2.02" intake), COME alloy rocker covers...$6600.00 383ci forged piston stroker kit, COME 4 barrel intake...$3300.00 383ci forged piston stroker kit, COME 4 barrel intake, COME 2009 complete alloy heads (2.02" intake), COME alloy rocker covers...$6900.00 396ci forged piston stroker kit, COME 4 barrel intake...$3600.00 396ci forged piston stroker kit, COME 4 barrel intake, COME 2009 complete alloy heads (2.02" intake), COME alloy rocker covers... $7200.00 355 forged piston stroker kit and COME Twin Throttle Body intake...$4500.00 delivered anywhere in Australia! 355 forged piston stroker kit and COME 2009 alloy heads complete...$5500.00 delivered anywhere in Australia! 383 forged piston stroker kit and COME Twin Throttle Body intake...$5000.00 delivered anywhere in Australia! 383 forged piston stroker kit and COME 2009 alloy heads complete...$6000.00 delivered anywhere in Australia! 396 forged piston stroker kit and COME Twin Throttle Body intake...$5500.00 delivered anywhere in Australia! 396 forged piston stroker kit and COME 2009 alloy heads complete...$6500.00 delivered anywhere in Australia! 355 forged piston stroker kit, COME Twin Throttle Body intake and complete 2009 ALLOY heads...$7500.00 delivered in Australia! 383 forged piston stroker kit, COME Twin Throttle Body intake and complete 2009 ALLOY heads...$8000.00 delivered in Australia! 396 forged piston stroker kit, COME Twin Throttle Body intake and complete 2009 ALLOY heads...$9000.00 delivered in Australia! LS1 Stroker kits...383, 408, 416, 420, 427, 440 featuring our 4340 forged steel cranks, Diamond Racing custom forged pistons, "H" beam 4340 steel con rods, new crank reluctor wheel fitted and indexed (24 or 58 tooth) assembly fully balanced internally...all $3600.00 delivered in Australia! Call today (03)9571-4204 or email come@comeracing.com Trade or urgent enquiries email workshop@comeracing.com 9:57:27 AM

	Friday, 28 May 2010

396ci Holden Street Stomper If you are restoring an early Holden, upgrading a later Commodore or Torana this is the "street" engine for you. The engine above makes over 480bhp @ 5500 rpm and over 480 ft.lbs of torque @ 4500 rpm. Runs on pump 98 fuel, has enough torque low down to be able to run highway diff gears and still run 11's in a typical VB-VL Commodore or Torana. We've fitted this engine with our forged piston 396 Stroker kit including Diamond Racing forged pistons our fully floating "I" beam 5.850" forged steel rods and fully counterweighted nodular iron crank all internally balanced. The late model block has been line honed and fitted with full main stud kit, an ASR oil pan, COME Racing HVH-234 hydraulic flat tappet cam and lifters, a cast iron high volume oil pump, Rollmaster timing chain and gear set. The top end features our latest 2009 alloy heads with stainless 2.02" and 1.60" valves, dual springs and moly retainers, roller rockers, screw in studs and guide plates along with hardened pushrods. The heads received a full CNC porting treatment and flow 645 hp through the intake ports. All the head work is not essential on a combination like this with relatively mild camshaft for the size of the engine. However we wanted to give customers the option of the fully ported heads to enable a combination like this to be used with more cam and compression if you want the 550+bhp level. These heads will easily support a 600bhp+ engine easily. Our latest COME Racing single 4 barrel manifold and alloy rocker covers are also fitted to complete the engine with brand new Bosch HEI electronic fully curved distributor and new Holley 750 double pumper carb. As an introductory offer this engine is to be sold OUTRIGHT, dyno run in with all the above components for $16,500! delivered anywhere in Australia. It's sitting in our shop waiting for a car to fit it to so call now, it won't last too long. Call today (03)9571-4204 or email come@comeracing.com Trade or urgent enquiries email workshop@comeracing.com 5:29:56 PM

	Thursday, 22 April 2010

427ci COME Racing all alloy street engine The COME Racing all alloy engine is an all alloy replacement for any Holden (Australian built 308-304) V8 engine. It seems that virtually all buyers of these magnificent engines are using them in early Holdens from HK-WB, Toranas or pre-EFI Commodores. You won't find a better value way to re-power the old clunker with a classic looking but modern technology pushrod V8 engine. This one was just completed for a customer and the next one is in production. Put your name on it now for $25,000 outright including, carb, intake, ignition, fully dyno run in and ready to fit. The bottom end has our billet 4340 steel crank, custom forged pistons, hydraulic roller valvetrain, our latest 2009 alloy heads and an ultimate Pro Series oil pan. The power and torque figures speak for themselves. Fuel used is pump 98 and just look at the torque as low as 2750 rpm. Who needs a blower when this type of grunt is possible normally aspirated. Call today (03)9571-4204 or email come@comeracing.com Trade or urgent enquiries email workshop@comeracing.com 5:47:08 AM

	Saturday, 20 March 2010

COME "SERIES II" Racing Heads Project 396 continues... A Holden V8 cylinder head that flows over 680bhp out of the box, utilizes current LS1/2 low friction lightweight valvetrain components including 8mm valves, conical springs for flat tappet applications, uses L92 Chev rockers with offset intake rocker arms, has huge oil drainbacks, accepts existing intake manifolds, extractors and fits any model Holden V8 blocks. The future of the Holden V8 has never been brighter. Our new alloy VN style racing heads will be ideal for stroker engines, particularly the "bigger" capacity engines used for serious street/strip or race only efforts. This new technology will enable the old Holden V8 to compete with any of the newest V8 engine designs in terms of power/torque per cubic inch (cc's). We wanted to bring the Holden in line with or even better than the current or previous factory best engines. Our Project 396ci Holden V8 engine is being fitted with these new heads first for a full session of developmental dyno tests in the next 4 weeks. Keep an eye on this space for the results... NEW! LS2 420ci Stroker kits... If you have an LS2, L98 or L76 6 litre LS type engine fitted to your late model Commodore or transplanted into an early car. Here's the best way to keep the engine looking stock externally while increasing capacity to 420ci or 6.9 litres of brute torque and power. Forget the blowers or turbos. This combination will rock the LS engine platform particularly in the heavier car where you don't want an overly cammy rough engine. Our full balanced kit includes our own 4340 forged steel 4.100" stroke crankshaft with fully indexed crank sensor wheel, our "H" beam 4340 steel rods, Diamond Racing custom forged pistons in .030" oversize, moly Total Seal rings, rod and main bearings all for the introductory price of $3600.00 delivered anywhere in Australia. NEW! LS3/L92 427ci Stroker kits. If you have a current L92/LS3 6.2 litre engine our new 427ci Stroker kit is for you. Same components as the above 6 litre version but to suit the LS3 block making final engine capacity...427ci (7 litre). Same price as well...$3600.00 delivered to anywhere in Australia. Call 03 9571-4204, email to workshop@comeracing.com for trade or urgent enquiries. Or email come@comeracing.com for all general enquiries. 8:44:43 AM

	Monday, 1 February 2010

383ci Holden Bracketmaster Engine The latest version of our popular 383ci engine packages shown above is one of many coming off the dyno regularly. Both EFI versions and carb versions are being built more than any other Holden V8 engines we currently offer. This latest engine featuring our new single 4 barrel intake, off the shelf Holley #4779 Double Pumper 750cfm carb, Bosch HEI electronic distributor, our 2009 VN style alloy heads (out of the box) unported and in this case a pretty conservative COME Cam part # HVH-234 hydraulic flat tappet design. In the bottom end, our forged piston 383 stroker kit with "I" beam 4340 steel rods and our nodular cast iron 3.750" stroke crank all spell ultra reliability. This engine made 480 bhp @ 5500 rpm and 470 ft.lbs torque @ 4500 rpm with over 420 ft.lbs as low as 2750 rpm. You simply could never have a better street engine with excellent manners and the ability to run low 11's in full street trim with streetable torque converter and street rear end gearing in the mid 3's at the most. We can supply all the parts for you to emulate this combination easily or if you provide us with your original 5 litre engine to build one the cost fully built and dyno run in...EFI or carb is $16,000 The EFI version has high flow injectors and our Twin Throttle Body EFI intake fitted. Such an engine is also available outright with no exchange for $18,000 This is a no brainer approach to incredible street/strip performance with realistic street manners for both city or highway cruising. 355 Holden Crank woes! In the past 12 months we've received many phone calls and emails from customers throughout Australia and even in New Zealand regarding the commonplace breakage of our competitors 355 Holden stroker cranks. As with everything in life, you will usually get what you pay for. Many trade customers who were buying OUR stroker cranks for years jumped on the "cheaper" crank bandwagon and have lived to rue the day they ever did this. Others, purely intent on maximising profit margins with little or no regard for the quality of the products they put in their customers engines, continue to play Russian roulette with your money by fitting the cheap and nasty cranks. We suggest you ask your engine builders whose crank or stroker kit they are going to use in "your" new engine. Make sure you specifically ask them to use our setup as you can rest assured the crank will not be breaking like those others which are badly designed and are cast using the cheapest materials available. COME Cams...we can supply tried and tested camshafts to help you achieve the correct end result from your Holden Stroker or LS1 engine based stroker projects. The flat tappet Holden cams are all $385.00 for virtually any of our huge range of hydraulic or solid grinds. All our LS1 cams are $550.00 Call or email us if you have any specific questions regarding any of our products or services. We are open 8.30am-5.00pm Monday to Friday Phone # (03)9571-4204 or (03)9571-9605 Email come@comeracing.com Trade enquiries workshop@comeracing.com 7:23:08 PM

	Saturday, 12 December 2009

COME RACING INTAKE MANIFOLDS and more... COME Racing has the market for Holden V8 intake manifolds covered when using VN style EFI type cylinder heads. Our ever popular EFI Twin Throttle Body intake manifold shown above in bare form is available with our popular billet dual 58mm Throttle body for street or strip use. It is also the basis of a fantastic Tunnel Ram dual 4 barrel or dual 4 barrel style throttle body intake. In fact these are usually also in stock with our billet dual 4 barrel adapter. Our latest single 4 barrel intake has already made great impressions with a power output in excess of the competition, fits under most bonnets avoiding the need for scoops and thereby attracting unwanted attention. These are now in stock for immediate delivery and only $770.00 We would like to take this opportunity to thank all our customers for their support throughout the last year and wish all a great and safe holiday season. 9:07:38 AM

	Sunday, 25 October 2009

NEW! COME SINGLE 4 BARREL HOLDEN VN INTAKE "IN STOCK NOW" Development testing completed The long awaited COME single 4 barrel intake manifold testing is complete. Results are what we wanted...a single 4 barrel intake to suit VN headed Holden V8 engines that fits under the bonnet, makes more power than all the others on the market, will be sold at a very competitive price and is made right here in Melbourne from Australian aluminium alloys. In fact on our 396ci Holden V8 development engine the new intake matched the power and torque output of a fully port matched Harrop single plane intake fitted with a 2" open hole spacer. Our intake had no spacer! This new product IS NOW IN STOCK. They are now ready to ship. Price is $770.00 Optional drilling for injector bosses...add $110.00 for those wishing to use our intake for EFI applications and retain the carb manifold look. The new manifold will work best on stroked Holden V8's from 355ci dispalcement and larger for both daily street use right up to competition oriented engines. The intake has proven to be an impeccable companion to our latest 2009 series alloy heads which featured greatly in the full development phase over the past 12 months of testing and refining. This is another product in the long line of newly engineered COME Racing products designed to maximise the output and competitiveness of the old Holden V8 with any other V8 engines available today. NEW! Flat tappet CAM profiles for Holden, Ford and Chev Small Block traditional V8's...we will list many new grinds that we've completed development on very, very soon. These allow power levels rivalling even roller profiles in some applications at a fraction of the cost of converting to roller setups. Stay tuned! Call 03 9571-4204 or (03)9571-9605 for more details of all our products. Or email workshop@comeracing.com Call or email for a free copy of our latest DVD featuring our latest product/services... come@comeracing.com UPDATE! 355ci Holden Stroker, COME 4 barrel intake, COME 2009 alloy heads, solid lifter COME cam part # CSBS-538. This combination just made 473 bhp @ 6000 rpm and 435 ft.lbs torque with 750 # 4779 Holley and Bosch HEI ignition on pump fuel. Production Commodore Pacemaker 1 3/4" Tri-Y extractors with 3" collectors were used in our test. Build one of these yourself with our $6600.00 355ci package deal of stroker kit, intake, heads and valve covers. All the development has been done so just do it! 8:18:13 PM

	Tuesday, 22 September 2009

New cams and lifters NEW VALVETRAIN PARTS... COME Racing has just completed development on several new LS1 camshaft profiles. These are a new High Lift range of cam grinds specifically designed to maximise power and torque from primarily modified LS1 style engines from 5.7 litres up. The new grinds available immediately are as follows... Part # LSCH-920 221 degrees intake and 231 degrees exhaust duration @.050" 114 degree lobe separation angle, .006" durations are 276/286 degrees and valve lifts are .609" for both intake and exhaust. Part # LSCH-964 228 degrees intake and 234 degrees exhaust duration @.050" 114 degree lobe separation angle, .006" durations are 284/289 degrees and valve lifts are .610" for both intake and exhaust. Part # LSCH-974 231 degrees intake and 240 degrees exhaust duration @.050" 114 degree lobe separation angle, .006" durations are 286/294 degrees and valve lifts are .617" for both intake and exhaust. Part # LSCH-930 230 degrees intake and 230 degrees exhaust duration @.050" 114 degree lobe separation angle, .006" durations are 286/286 degrees and valve lifts are .609" for both intake and exhaust. Part # LSCH-923 236 degrees intake and 246 degrees exhaust duration @.050" 114 degree lobe separation angle, .006" durations are 293/303 degrees and valve lifts are .617" for both intake and exhaust. These new high lift designs are ideal for more competition oriented applications particularly with modified engines. Ideally suited to engines with improved high valve lift air flow characteristics and raised compression ratios from stock. The part # LSCH-930 is an excellent turbo application profile in 6 litre or larger engines. All these cams can be ordered with different lobe centre separations if required. All our LS1 cams are $550.00 each We are also very close to completing development on a new range of flat tappet solid lifter profiles to suit traditional Holden, Ford and Chevy V8 engines These are basically designed to produce excellent power and torque rivaling the overall output of equivalent solid roller lobe shapes in many cases. To accompany the solid lifter GM engine application camshafts we now see the return of the famous and sorely missed EDGE ORIFICE SOLID LIFTERS to suit Holden and Chev V8 engines. These wonderful lifters virtually eliminate the problem of excessive top end oiling normally associated with conventional flat tappet solid lifters. If you are a racer or have a powerful weekender buildup coming up these lifters are the only way to go to keep your bottom end alive. The Edge Orifice design restricts oil to the the valve covers dramatically, keeping oil in the sump where it needs to be to keep your oil pickup covered. This prevents the proverbial "run" bearings and other oil starvation problems. The Edge Orifice lifters also immediately increase overall oil pressure by getting rid of a major drainage point of oil from the lifters themselves. At $220.00 a V8 set they are one of the biggest reliability enhancements you will ever find for virtually peanuts in cost. Our great deals on all our LS1 and Holden V8 Stroker kits, EFI Holden intakes and fantastic 2009 VN style alloy heads are still continuing. Call or email for some incredible value for money package deals. Don't forget our ever growing range of state of the art camshaft profiles for LS1, Holden, Ford and Chev V8 engines. Call 03 9571-4204 or email come@comeracing.com Trade customers please call or email workshop@comeracing.com We have just produced a DVD presentation which highlights some of the features of our latest products, some of our machining services, a few visual explanations relating to properly clearancing your Holden V8 block for stroker applications and details of a new Holden V8 racing cylinder head we are close to completing development on. Call or email us for your free copy today. 8:01:35 PM

	Saturday, 1 August 2009

383 Holden Street-Strip daily driver So many of the calls we receive almost daily are from customers asking about "THE IDEAL COMBINATION". Well our job is to take the guesswork out of building performance engines everyone can live with while maximising the performance and reliability potential. In other words the BEST VALUE for MONEY combinations that satisfy performance, reliability, driveability and even fuel mileage parameters to an optimum at a value for money overall cost. Today this is very feasible. In fact it has never been more possible to produce combinations that fulfil ALL the requirements of today's performance enthusiasts. Case in point is the Holden Stroker V8 engine featured above. This is a 383ci (6.3 litre) stroker fitted with the following components in a truly bolt together form by ANYONE! 1) COME 383 forged piston stroker kit, nodular cast 3.750" stroke centre counterweighted crank, forged 4340 steel "I" beam rods with ARP bolts, King rod and main bearings, Hastings moly rings with the whole assembly internally balanced. Kit cost...$3000.00 2) COME 2009 VN style alloy head package with 2.02" and 1.60" stainless valves, dual 1.450" springs and moly retainers, positive seals, full 3 angle valve job. Heads flow over 580 bhp @ .700" lift but more importantly they flow over 560 bhp @ .500" lift where the cams likely to be used in this combo are designed to work at. We've spent over 10 years developing this latest combustion chamber and the results definitely show it was worth the wait. Exhaust flows over 116 cfm @ 10" depression. Complete heads cost...$3500.00 3) COME CLH-775 hydraulic flat tappet camshaft and lifters. Cam and lifter cost...$550.00 4) Block machinework: Hot tank acid bath cleaning, remove and replace camshaft bearings, line hone main bearing tunnels and fit main stud kit, clearance grind for swing of stroker components (you will never hit through water jackets with our 383 "I" beam rod kit), bore and torque plate hone cylinders to .030" oversize, prep clean and mock assemble then deck block to square to set piston deck heights, fit new brass welsh plugs. Cost of block machinework at COME Racing workshop...$2500.00 5) COME Racing alloy valve covers...$550.00 (can also use stock factory VN-VT covers) Other off the shelf parts needed... 1) Redline Hi Winder low rise single plane intake 2) Hi Energy or other Street oil pan with extra capacity and clearanced for 383 crank 3) Bosch HEI with correct spark curve or complete adjustable ICE ignition system 4) Any good quality alloy roller rocker set in 1.65:1 rocker ratio 5) Screw in studs, guide plates and hardened pushrods 6) Stock GM or Austral cast iron oil pump 7) Rollmaster timing chain and gear set 8) Holley # 4779 750cfm Double pumper carb and open hole alloy 1" carb spacer...Speco brand 9) Powerbond steel harmonic balancer 10)Full gasket set either Genuine GM for VN-VT 5 litre or aftermarket "graphite" gasket set As one can see it's really a no brainer. All parts on this engine are "off the shelf". The intake manifold was checked for port match and corrected as required to match intake ports. The carb as shown in our tests did not even have a jet change and would be fine as is for 90% of locations around Australia. The ignitions tested were both a stock Bosch HEI with 26 degrees total timing @ 3400 rpm. The ICE ignition was supplied by our customer and was calibrated much more easily to similar specs with the flick of a switch on the ICE control box. Results were the same when used on BP 98 pump fuels despite the 10.9:1 compression ratio. Once again, this is a by-product of the fantastic efficiency of the latest combustion chambers in our 2009 heads. Just buy this bunch of parts, get your block machined and bolt together this 480+BHP (357KW) street engine at a low 5500 rpm with brute 465 ft.lbs torque (630nm) at 4500 rpm and over 400 ft.lbs as low as 3000 rpm. Imagine this engine in any model Holden from a HK through to VL Commodore or Torana. In the lighter cars this engine will run 10's all day and only needs a set of Pacemaker or similar Tri-Y 1 3/4" primary extractors and a decent dual 2.5" or 3" system to maximise results. Once again, off the shelf parts with only needing the collectors modified to dual 3" outlets preferably. We've spelled it out for you...a combination you cannot beat for the money. More importantly there are no exotic parts, custom modifications, or spin from so called experts claiming they can do a "special custom" combination for you for lots more money with potentially dubious results. Don't be misled, this is a real deal which will satisfy all your requirements for a weekender, daily driver, bracket racer and long distance cruiser on pump fuel. It's never been easier to make LS1 type power reliably from your Holden V8...what are you waiting for? See this engine running http://www.youtube.com/watch?v=2e6Dq5qBnG8 Call us on (03)9571-4204 or email come@comeracing.com for further assistance or to order any of our products. Trade customers please call or email workshop@comeracing.com 8:55:50 AM

	Saturday, 11 July 2009

396ci Holden Project #1 fires up!   The results really speak for themselves. This first "Project 396" is a bolt together with off the shelf parts... 1) Factory 304ci block, fully machined with our steel 4 bolt main caps fitted, clearanced for our 396 "I" beam rod, nodular cast crank, forged piston stroker kit. Block is bored, torque plate honed, decked to square, machined with "O" ring grooves on decks and "O" rings fitted, modified oiling system. 2) 396ci Stroker kit as above with a final compression ratio of 11.9:1 is fitted to the short block. 3) Our custom CSBS-720-112 solid lifter flat tappet camshaft is fitted. 4) Our latest 2009 series alloy VN style cylinder head package with Ferrea 2.08" intake and 1.60" exhaust valves, COME dual 1.450" valve springs and moly retainers and locks. Positive stem seals, screw in studs, guide plates, hardened moly pushrods, Crane cast alloy street type roller rockers in 1.6:1 ratio (Ford Windsor type). Heads flow 636hp through intakes and 126cfm @10" through exhaust ports. Heads are topped off by our new alloy valve covers making valve lash settings a flash. 5) Harrop single plane intake manifold port matched (others to be tested) and out of the box Holley Pro Series 950cfm carb. Two inch open carb spacer. Did we mention that 586bhp and 502ft.lbs torque was made on Caltex 98 pump fuel! 6) Bosch HEI distributor boosted by an MSD 7 Digital ignition box and coil. 7) Off the shelf Pacemaker 1 3/4" Commodore Tri-Y extractors with 3" collectors replacing the normal 2 1/2" outlets supplied by Pacemaker. These are actually our dyno test pipes. Aside from the collectors they are off the shelf. 8) For our testing purposes we have also replaced the usual Rollmaster double row competition timing chain and gear set with a new belt drive assembly supplied by Heads Racing in New Zealand. This is to enable fast cam dial in, cam timing adjustments and cam changes without removing balancer and timing case each time. This is also a wonderful product for those building serious effort Holden V8's. The $1950.00 price is a bargain considering this is all CNC machined from billet alloy rather than being a casting. What does it cost? 396ci Stroker kit...$3300.00/  COME 2009 2.08" alloy heads...$5000.00 a pair complete/ COME valve covers...$550.00 a pair/ Any COME flat tappet camshaft...$385.00 At this stage these are the main parts to make the 396 project become a reality. There are several intake manifold and cam choices and we will test a number of these soon. It's also easy to build a more conservative 500 to 550 bhp version that's daily driveable in either EFI or carb form. To do this and more you will only need our out of the box 2009 alloy heads with 2.02" valves priced at $3500.00 a pair. It's never been easier to make LS1 type power reliably from your Holden V8...what are you waiting for? Call us on (03)9571-4204 or email come@comeracing.com for further assistance or to order any of our products. Trade customers please call or email workshop@comeracing.com   9:05:18 AM

	Wednesday, 29 April 2009

COME Racing Alloy head range expands In these tough times we are spending enormous time and effort in the development of new and improved versions of all our products. Our latest 2009 VN Holden V8 alloy heads are just the tip of the iceberg. These heads are the FIRST and only Holden V8 heads on the market to be a true out of the box bolt on power maker with ZERO porting required for engines up to at least 550bhp. Bottom line, bolt these $3500.00 per pair complete heads on your street or strip Holden V8 and they are equally at home on a mild 380bhp daily driver 355 or a Bracket Race 383/396 stroker making over 550bhp. With small 182cc intake runner volumes for incredible air speed and over 570bhp potential through these small high velocity runners you will always make the best possible power and torque compared to fully ported cast iron heads and any other alloy heads on the market today. This is a simple fact of life and most importantly the cost is actually lower per cfm of airflow than anything on the market today. We realise traditional head porters are not happy because they are no longer needed to modify factory or other aftermarket heads for you to make maximum power. To that end however, we have also catered for the higher power level applications right up to full race engine needs in a new collaborative effort with renowned 5 axis computer numerical control cylinder head porting company Bullet Cylinder Heads in Adelaide http://www.bulletcylinderheads.com.au/ They have developed some incredible automatic machine ported combinations using our latest 2009 castings. For those of you wanting to maximise results with primarily big capacity engines or race applications Bullets fully machine ported heads will outflow anything else on the market by a large margin. The Bullet computer ported COME 2009 heads are available direct from Bullet or from COME Racing. Making big power from your Holden V8 has never been easier with parts you can take out of the box and bolt together. For example...take our 355 forged piston Stroker kit, our out of the box UNPORTED 2009 alloy heads complete and our COME Racing Twin Throttle Body intake. Use one of our hydraulic flat tappet streetable cam profiles and you have a genuine 450bhp easily. Want to go bigger, the same applies to our 383 and 396 versions which make insane torque as well as power. 500+bhp in fairly streetable engines is now very straightforward. You want to race more than street drive? Add our new 2009 Computer ported street heads to a 383 or 396 engine and make 550+ bhp with absolute ease on pump 98 octane fuel. A complete pair of these computer ported heads which flow over 640bhp are $5500.00 per pair including full valve seat job, dual flat tappet 1.450" springs, moly retainers and locks, positive stem seals, solid bronze valve guides, Ferrea stainless steel extra length 2.08" intake and 1.60" exhaust valves. Remember also our NEW Holden VN V8 style single plane single 4 barrel carb intake manifold will be available very soon to totally rewrite the power potential of carbed combinations of the big cubic inch Holden V8's. We will now have you covered for EFI or carb intake. You all know the reputation of our EFI manifold. The new carb intake will provide the same boost to carbed combinations as the sorely needed EFI version did all those years ago. A new level of performance has been needed for the carb intake for many years, it will soon be here. Remember also...COME Racing heads are fully designed, developed and manufactured right here in Australia. The quality of materials and machining is second to none so if you are tempted to look at the junk coming from Asia we suggest you spend more on the local product because in the long run our local product will actually prove to be the lower cost alternative. Don't just think with your hip pocket nerve, it will bite you when you realise you have bought an inferior product that cannot produce the results of ours no matter what you are told. Contact us for a deal on any of our products...from alloy heads, alloy cylinder blocks, intake manifolds, valve covers, camshafts, stroker kits and more for your Holden V8. LS1 stroker kits, camshafts and engine combinations. Holden V6 stroker kits, camshafts and Ecotec intake manifold and much, much more. Phone (03)9571-4204 or email come@comeracing.com Trade enquiries or urgent enquiries to workshop@comeracing.com   6:10:23 AM

	Sunday, 26 April 2009

396ci Holden Project continues...  A Bracket Race version of one of our Holden 396ci Stroker engines is nearing completion. A camshaft belt drive system is employed to enable fast cam changes and phasing for rapid test purposes. The new 2009 series COME Alloy heads are virtually ready to be fitted but we are waiting for delivery from the foundry of our new single plane single 4 barrel intake manifold to be part of the test regime. Stay tuned... As proud Australians we pay tribute to the ANZACS who sacrificed to ensure we live in a free society to pursue our passions in peaceful harmony. "Lest we forget" 7:09:21 AM

	Saturday, 4 April 2009

Holden V8 EFI engine combinations   Some wonderful Holden V8 engine combinations are available right now. No stressing about "the right or wrong combinations". Our experience with the Holden EFI V8 is unmatched anywhere. Our developed combinations are streetable, clean as far as emissions is concerned and actually very fuel efficient. The latest 2009 version of our VN-VT style alloy Holden heads is being flowed on our 660cfm digitally controlled flow bench. Many hours of research yields wonderful products. Be aware there are cheap imported parts these days that will never produce the results and reliability being promised. In stock right now we have the following popular engine combinations sold on a changeover basis for your original stock 5 litre EFI Holden V8... 355ci (5.7) Holden S.S-1 EFI COME Twin Throttle Body engine package. Featuring...280kw and 542nm torque (380bhp & 400ft.lbs) This fully built, assembled, dyno run in and tuned engine is...$11,000.00 changeover. It includes our KB hyperuetectic piston stroker kit, COME Twin Throttle body intake and fully ported cast iron factory heads.   383ci (6.3) Holden S.S-3 EFI COME Twin Throttle Body engine package. Featuring...320kw and 596nm torque (430bhp & 440ft.lbs) This fully built, assembled, dyno run in and tuned engine is...$15,000.00 changeover. It includes a forged piston 383 stroker kit, COME Twin Throttle body intake and our latest 2009 ALLOY heads with roller rocker valvetrain.   396ci (6.5) Holden S.S-3 EFI COME Twin Throttle Body engine package. Featuring...345kw and 624nm torque (460bhp & 460ft.lbs) This fully built, assembled, dyno run in and tuned engine is...$16,500.00 changeover. It includes a custom forged piston 396 stroker kit, COME Twin Throttle body intake and our latest 2009 ALLOY heads with roller rocker valvetrain.   For those of you who prefer to build your own...our components packages will definitely interest you. 355 forged piston stroker kit and COME Twin Throttle Body intake...$4500.00 delivered anywhere in Australia! 383 forged piston stroker kit, COME Twin Throttle Body intake and complete 2009 ALLOY heads...$8000.00 delivered in Australia! 396 forged piston stroker kit, COME Twin Throttle Body intake and complete 2009 ALLOY heads...$9000.00 delivered in Australia! We can also help with accurate cam selection information from our huge range of available profiles. Most flat tappet cams are $385.00 All the above engine combinations feature flat tappet hydraulic grinds from our range and the combinations have been fully developed to properly complement the engine efficiency, torque and power outputs. Contact us for full details of any of these Holden engine and component combinations as well as our popular LS1-LS2-LS3 engine and components deals. Phone (03)9571-4204 or email come@comeracing.com For urgent enquiries as well as Trade enquiries phone us or email workshop@comeracing.com   1:19:02 PM

	Sunday, 22 February 2009

COME Racing 2009 VN-VT Holden alloy heads NEW! The latest version of our ever popular alloy heads for Holden V8 engines is now available. 1) NEW! Redesigned combustion chambers for maximum swirl and burn efficiency. 2) NEW! Spark plug moved for maximum burn while still working with production extractors. 3) Stellite interlocking valve seats for use with any fuels. 4) NEW! solid phosphor bronze valve guides for maximum strength and service life. 5) NEW! increased amount of solid alloy material in water cores for maximum porting potential, feasibility to deepen and widen spring seats for any available roller or flat tappet springs. More material in decks, intake and exhaust faces for incredible strength under extreme loads. 6) NEW! redesigned intake and exhaust ports for maximum airflow with increased velocity. Low, mid and high lift flows improved by over 10% in most areas. Intake port volume kept to a small high velocity 183cc size for vastly improved torque and engine acceleration potential. 7) NEW! these are truly the first and only Holden V8 alloy heads designed to be used right out of the box with absolutely NO porting whatsoever. With a proper valve job only, the intakes flow over 545 bhp @.500" valve lift, over 570 bhp @ .600" lift and over 588 bhp @.700" lift with a small 2.02" non undercut intake valve. This is with no bowl blending or porting whatsoever. 8) NEW! race potential without porting never before seen. Throat the installed intake seats to a 2.08" valve size with a proper valve job and very minor bowls blending to one centimeter below the bottom seat and the same small 183cc intake runners flow over 630 bhp @.700" valve lift with still incredibly strong low to mid lift flow numbers. This latest technology street/strip head from COME Racing will outpower and out accelerate anything else on the market. By the way, get in there with the right porting and you will see awesome flow numbers for race only applications. However, we strongly suggest if you are building a great street/strip engine that you forget about the porting altogether, you simply won't need it. Opening the port volume further by porting the heads will see flow gains but only at the upper valve lifts suitable for race only applications. Keeping the volumes smaller keeps the air speed or velocity very high and promotes incredible torque curves and throttle response while enabling huge power gains with the right combinations. Heads as before are available bare with only guides and seats installed for $2750.00 per pair. Or as a complete package including our 2.02" intake and 1.60" stainless intake and exhaust valves, full valve job to maximise air flow potential, dual coil flat tappet or hydraulic roller application 1.450" springs and chrome moly steel retainers on hardened steel spring locators to protect the alloy spring pockets, positive valve stem seals and gasket faces finish machined to approximately 62cc equalised volumes. Other chamber volumes also available.  The complete 2009 head package is still only $3500.00 per pair fully assembled. To complete your engine we now have finally released our beautiful new cast alloy non leak valve covers to really complete any Holden V8 engine. These are $550.00 per pair and feature 4 bolt fastening with capscrew bolts (supplied), oil filler cap, baffle plates for PCV or breather vent raw oil restriction and are drilled and tapped for front mount right angle breather fittings (supplied) to accept hoses like the OEM VN factory design. You have the choice of a fully clearanced cover to clear the VN-VT Commodore brake booster on the drivers side cover or to buy the covers without the special clearanced Commodore version for a more uniform look in all other model cars where symmetrical appearance is more important. Kit deals... 1) Holden V8 alloy head package deals...  latest design 2009 heads complete volume needs heads are $3500.00 per pair complete. NOTE: these heads flow over 588hp through intake ports. OR...The above heads and our Holden EFI Twin Throttle Body EFI intake manifold purchased together for $5500.00 2) ECOTEC or VN-VR V6 4.2 Stroker kits...BOOST application kits with the absolute strongest parts available anywhere for the Holden V6 engines. These balanced kits feature our 4340 steel billet stroker cranks, our 4340 steel "H" beam rods with ARP2000 series bolts and either Wiseco or Diamond Racing custom forged pistons, moly rings, rod and main bearings all for $5000.00 (same kit with cast crank for $4000.00) Get that V6 ready for the track with V8 humbling power and reliability. 3) 355ci Holden V8 Stroker kit, billet steel crank, “H” beam rods, forged pistons. Available in normally aspirated or boost style low compression pistons…$4900.00 5) 383ci Holden V8 Stroker kit, billet steel crank, “H” beam rods, forged pistons. Available in normally aspirated or boost style low compression pistons…$4900.00 6) 396ci Holden V8 Stroker kit, nodular cast iron 3.8750" stroker crank, "I" beam 5.850" fully floating 4340 steel rods, custom forged pistons (several compression ratios available), fully internal balanced, moly rings, rod and main bearings all supplied...$3300.00 full kit Bargain deal...With every set of our complete 2009 VN style Holden V8 alloy heads...when ordered together with either our 355ci or 383ci Stroker kits you will receive FORGED PISTONS FREE! The deal means you receive our complete pair of alloy heads, a 355 Stroker kit with nodular cast crank, forged 4340 steel "I" beam rods and forged pistons all for $5500.00 The same deal with our 383ci Stroker kit is $6000.00 By far the best quality Holden V8 products at the best prices.  396ci project version # 1 nears completion...Our first 396ci Holden V8 project engine will be ready soon. Fitted with our latest 396 stroker kit and new 2009 version alloy heads. This will give you all a baseline formula for a street engine with great manners, life potential and even fuel economy that will run low 11's to high 10's on pump fuel in a typical late model VB-VS Commodore. Quicker times for the lighter models but still pretty insane performance from a reliable long life engine anyone can build with our bolt together components. For more details on all our products including turn key engines, stroker cranks and kits, heads, intake manifolds etc. call during business hours (03)9571-4204 or email us at come@comeracing.com All trade enquiries email to workshop@comeracing.com   4:58:34 PM

	Saturday, 22 November 2008

408ci LS1/LS2 Short motor SALE! If you have a tired 5.7 LS1 or 6 litre LS2 engine, there has never been a better time to rejuvenate your cars powerplant. We are offering brand new 408ci Short motors built using new 6 litre GM blocks and our PREMIUM Stroker kits. A fully machined 6 litre block containing our "best" stroker kits featuring our own 4340 steel 4.00" stroke forged cranks, "H" beam rods and custom forged pistons for either boost or normally aspirated applications. The complete rotating assembly is fully balanced internally, cranks are fitted with new GM crank angle sensor, new blueprinted oil pump, Powerbond keyed balancer, your choice of billet COME camshaft and timing set...OUTRIGHT for $7500.00 This fully assembled short motor will accept your complete LS1 or LS2 top end including intake, heads and all other original ancillaries like oil pan and other bolt ons to complete the engine. We can rebuild your original cylinder heads for you to fully compliment the new short block including full acid bath cleaning, crack testing, new bronze valve guides, full three angle valve seat job, a set of our COME125 conical performance valve springs and positive valve stem seals fitted, heads fully face machined to equalise chambers and optimise compression ratio...all for $1995.00 a pair fully assembled. This is the basis of a bargain rebuild capable of making over 530bhp and at least 530ft.lbs torque in a normally aspirated daily drive combination. COME CAMS! COME Racing is still the only camshaft manufacturer in Australia that designs and tests every profile in house in our own engines on our own engine dyno. We know we are not the lowest price cam supplier but with the recent fall in the Australian dollar versus the U.S dollar, prices of imported cams will inevitably rise bringing our products closer to the U.S versions. The real point of course is that price is not everything in the performance parts market. You need to realise that each of our cams is ground in house by someone with a lifetime of experience on a truly custom basis. Every cam is hardness tested for material consistency, then surface finish tested to ensure the smoothest interface between lifter and lobes and finally straightness checked to ensure valve timings are consistent cylinder to cylinder. All our roller cams have micropolished lobes to ensure surface finishes of under 5 RA for the longest possible life and minimum friction between lobes and lifters. This attention to detail and the fact that we are the best equipped knowledge source for choosing the right profile the first time is why you need to buy our cams. There is no substitute for experience in design, testing and manufacture of a critical product like your engines camshaft...I'm the person who will be grinding your cam...you can rest assured it will be the best quality product you will find anywhere...They don't call me "Sam the Cam" for nothing! Go to the "cam" section of our website http://www.comeracing.com/products/cams/ and then send me a message if you need guidance on an appropriate profile selection. Contact COME Racing from Monday to Friday 8.30am to 5.00pm on (03)9571-4204 or email come@comeracing.com Urgent or trade enquiry emails to workshop@comeracing.com 7:08:04 PM

	Saturday, 25 October 2008

Olds Cutlass Pro Stock car for sale This is your chance to buy the best Olds Cutlass Pro Stock car in the country. Available as a rolling but complete car less engine and transmission. This car was built brand new in 1996 by Jerry Haas Race cars in the U.S It held the Australian A/AP National record for many years and consistently ran very low 7's @ over 190 mph. Was runner up in the 1999 Australian Nationals in Comp Eliminator and was always a feared opponent when it was raced. The car has done no more than a total of 200 passes since new and has always been pampered and impeccably looked after. Many items were updated in 2006 including the fitting of the latest technology Lamb struts and bigger brakes front and rear. New lightweight Weld wheels front and rear as well as state of the art tyres were fitted. New Stroud dual "launcher" parachutes were fitted. The latest Jerry Haas wheelie bars and anti roll bar assembly were also part of the updates to this already awesome full chrome moly Jerry Haas chassis. Supplied with the car are the following...Racepak Computer Data logging system, 2 virtually brand new Mark Williams Big pinion aluminium Pro Stock low friction diff centres and Mark Williams 40 spline axles, almost new Trick Titanium bellhousing drilled for Lenco or liberty transmission, MSD Digital 7 ignition, full Barry Grant 400 fuel system in the rear as well as a front mount fuel cell assembly built by Jerry Haas for the car, 16 volt Turbo Start race battery, all Autometer instruments, doors and front clip are the best full carbon fibre items and we also will supply a complete brand new carbon fibre (spare) front clip assembly, a pair of genuine Pro Jacks with air/hydraulic operation for lifting the car safely, fold away door stands to support doors during between round service or storage, Koni fully adjustable rear shocks plus a brand new Koni Electric shock system (we never got around to fitting), several sets of interior tin work to suit Liberty trans, 5 speed Lenco, G-Force trans, new Mark Williams alloy driveshaft, 240 volt clutch disc surfacing machine, 2 additional sets of rear race Weld Wheels and one pair rear slicks, fitted to this car is Jerry Haas race car ABS system for safer top end braking, hood scoop to suit dual Dominators which can easily be altered for use with different carbs or carb. Price is $75,000 for the lot. All you need do is drop an engine and transmission in from 500-1500 bhp and go enjoy yourself. Car is equally at home in any class you want to race, Super Sedan to Super Stock or Pro Stock etc. You will not buy a better top of the line Drag race car in Australia today with such low mileage. Car goes straight as an arrow and will hold its value very well. Call Sam on (03)9571-4204 or email come@comeracing.com for more photos or any other questions you may have. Photo courtesy Dragster Australia Magazine http://www.dragsteraustralia.com.au 6:13:06 AM

	Sunday, 31 August 2008

LS1-LS2 V8 Stroker kit deal Stroker kits LS1 V8.   (all kits fully computer balanced, internally)     PREMIUM KITS…   383ci LS1 V8 (6.3 litre) Stroker kit with Wiseco or Diamond Racing forged pistons and 4340 steel “H” beam conrods, forged 4340 steel 4.00” stroke  crank. Kit includes moly race rings, rod and main bearings, new GM crank angle sensor fitted and indexed with whole assembly internally balanced…$3800.00 Available in hi comp or low comp boost piston versions.   408ci LS1 V8 (6.7 litre)  Stroker kit with Wiseco or Diamond Racing forged pistons and 4340 steel “H” beam conrods, forged 4340 steel 4.00” stroke crank. Kit includes moly race rings, rod and main bearings, new GM crank angle sensor fitted and indexed with whole assembly internally balanced…$3800.00 (note: must use LS2 or any 4.00” bore block. Available in hi comp or low comp boost piston versions.   416ci LS1 V8 (6.8 litre) Stroker kit specifically for the 6.2 litre LS3 engines. Includes custom forged pistons, our “H” beam 4340 steel conrods, forged 4340 steel 4.00” stroke. Kit includes moly race rings, rod and main bearings, new GM crank angle sensor fitted and indexed with whole assembly internally balanced…$3300.00 (note: must use LS3, 4.060” bore block. Available in hi comp or low comp boost piston versions.   427ci LS1 V8 (7.0 litre)  Stroker kit with Wiseco or Diamond Racing forged pistons and 4340 steel “H” beam conrods, forged 4340 steel 4.00” stroke crank. Kit includes moly race rings, rod and main bearings, new GM crank angle sensor fitted and indexed with whole assembly internally balanced…$3800.00 (note: must use LS7 or any 4.125” bore block. Available in hi comp or low comp boost piston versions.   440ci LS1 V8 (7.3 litre)  Stroker kit with Wiseco or Diamond Racing forged pistons and 4340 steel “H” beam conrods, forged 4340 steel 4.100” stroke crank. Kit includes moly race rings, rod and main bearings, new GM crank angle sensor fitted and indexed with whole assembly internally balanced…$4200.00 (note: must use LS7 or any 4.125” bore block.) Available in hi comp piston versions only.   We have very reasonable freight rates Australia wide and can arrange shipping to anywhere in Australia. Call us on (03)9571-4204 or email workshop@comeracing.com for immediate response to questions or to place orders.   7:09:04 PM

	Saturday, 9 August 2008

The heart of your engine, the CAMSHAFT...   Still one of the most misunderstood components in performance engine building today. You can use the latest computer simulation programs, read the flashy catalogues, go on the forums to be misled day in day out. The bottom line is the only people capable of really choosing a camshaft profile correctly are those who really know and understand how an engine works. Those who build engines all day long and test thousands of combinations to find optimum components matches. Those who actually design and manufacture engine components including camshafts and test their theories day in day out on an engine dyno to really evaluate the torque curves they are looking for. Most importantly, those who really love their craft and get real satisfaction out of creating a component mix that does everything and more it is supposed to. If you look around Australia's performance industry you will not find any other company here that goes to the trouble and expense of developing performance components designed to work to maximise your results on the street or race track. Before just buying a camshaft or any performance product being recommended by the local performance guru, do some research yourself. It may save you the grief of finding that the 1st selection of components, particularly the camshaft, did not produce the desired effect. Our COME Cams are designed using the latest software which takes into account an incredible range of valvetrain dynamics, weights, valve motion characteristics and valve spring rates. Our master cams are then machined on CNC grinding machines to almost immeasureable accuracy. This final master cam is then used on our in house grinders to produce the most accurate cam profiles possible. That's only the beginning. We verify the effectiveness of every profile in custom built dyno test engines to ensure the designs produce exactly what they are supposed to...maximum power and torque, maximum valve train stability for long valve train life and the quietest possible operating efficiency. There's more to making a cam than just copying someone elses grinds. We prefer to design and test our own ideas before they end up in your engine and you become the "test mule". A camshaft is indeed one product you want to get right the first time, it effects your whole engine combination dramatically because it truly is the "heart of your engine" regulating almost everything that the engine produces. If you think about it carefully can you imagine the number of camshaft types there really are? Automotive, motorcycle, petrol, diesel, aircraft, marine and lots more. COME Cams does only cams for very specific engine types. We narrow our focus because it's impossible to cover all those possibilities successfully and achieve maximum results from all of them. There are simply not enough hours in the day to devote to a real development program to cover all bases. Most cam companies buy existing performance grinds and copy them to enable them to extend their master cam libraries. The problem with this logic is that copies are never quite the same as the original. Frankly, if one does not know the diameter of the grinding wheel used to make the donor cam then the copy cannot be accurately reproduced. We prefer to design and develop our own range of profiles with todays technology. Our results in the cam industry have been documented over more than 20 years by successful racers and street users throughout Australia. COME Racing manufactures cams for Holden V8, Chev LS1/LS2/LS3/LS7 V8, Holden V6, Ford V8's, Chev Small and Big Block V8's. Our cam product range to suit these engines is by far the most advanced technologically in Australia and we work hard to keep it that way. When you need a camshaft to suit these engines it would be useful for you to email us at workshop@comeracing.com for an urgent cam recommendation and pricing, or to come@comeracing.com for cam or other product enquiries. Remember, the cheapest cam you can buy is the one that works best the first time. If you still prefer to choose your own profile, as us for our complete catalogue. We can email this or post it to you in hard copy by regular post. You can of course call us during business hours on (03)9571-4204 for help with all our products. 6:20:36 AM

	Thursday, 17 July 2008

BOOST Stroker kits and engines With the popularity of boost setups these days, both turbos and superchargers we have some great engine components to enable strong reliable engine buildups to suit boost applications... 4.2 Ecotec V6 BOOST capable short motors: These are sold outright and include a fully machined Ecotec cylinder block. Bored and torque plate honed, "O" ringed decks, copper head gaskets supplied, nodular cast iron stroker crank (capable of 15psi+ boost), "H" beam 4340 steel con rods, Wiseco or Diamond Racing custom low compression forged pistons. Assembly fully balanced for use with Ecotec balancer and flywheel. Short is supplied with matching boost billet cam and timing set. Oil pump, timing set and steel Powerbond harmonic balancer and sump fitted...OUTRIGHT for $6500.00 (unassembled for $5800.00)...Optional billet steel crank...add $1500.00 (more extreme boost capacity) Long motors including ported ST-3 heads and our new Twin Throttle Body intake manifold...$12,000.00 outright 355ci Holden V8 Boost short motors: Available outright or we do your late model standard bore cylinder block. Includes fully machined block with our billet steel 4 bolt main bearing caps fitted, clearanced for stroker, decked and "O" ringed supplied with copper head gaskets. Fitted with a our best 4340 steel billet 355 crank, "H" beam rods and custom Diamond Racing low compression forged pistons. Rotating assembly is fully balanced internally...OUTRIGHT for $11,000.00 or using your block for $10,000.00 Call or email us for all your Stroker crank kit, camshafts, cylinder heads or engine needs. The Government may not know how to control inflation but we do with our prices dropping rather than increasing. Your continued support makes this possible. With volumes up we are able to cut production costs and can pass these on as often as possible. It's not doom and gloom out there, we can still all have our performance needs and enjoy our leisure time and hobbies. The key is to choose wisely the first time and buy the right parts for the job you wish to do. Not go and buy the parts which appear to be the cheapest on the market. False economies are everywhere and people seem to be sucked in by a low price till they learn the hard way. Email... come@comeracing.com Urgent enquiries and trade enquiries... workshop@comeracing.com  Call us on (03)9571-4204     5:22:12 AM

	Saturday, 19 April 2008

440ci LS1 Piledriver   Want maximum capacity out of your LS1 equipped vehicle. Our 440ci version is a lot of engine for any application. These big engines are quite tractable even with large camshafts, big inductions and high compression ratios. We offer the 440's in power levels from a mild 550 bhp (410kw) version for exceptional daily use manners up to very radical versions for more extreme owners. This version shown here was built for a customer who named the engine for us...the PILEDRIVER! Still a very tractable but powerful version with typical moderately rough idle, pump 98 octane fuel capability and torque to rival a Mack Truck. The Piledriver version has CNC ported GM Performance parts heads with final intake port volume size of close to 280cc's. True Big Block numbers with air flow to match. Over 11.5:1 compression ratio, our latest design LSCH-945 camshaft with 245/257 degrees @.050" intake/exhaust, .560" lift and ground on 114 degree lobe centres. This like all our LS1 style grinds do not sacrifice power and torque output for smooth valve train action and quiet operation. The bottom end features a brand new GM alloy 427 (7 litre)LS7 cylinder block that has been fully prepped and fitted with our 4340 forged steel 4.100" stroke crank, our latest design 6.1" "H" beam 4340 steel con rods and custom made Diamond Racing forged pistons and rings. The top end is completed with GM's latest L92 square port intake and our own custom made billet alloy 95mm throttle body. The Piledriver is not cheap at a baseline $25,000 (depending on outright or changeover) but with 626 bhp (467 kws)@ 6000 rpm and 594 ft.lbs torque (805nm)@5200 rpm in a very driveable and still fuel efficient combination, you would be hard pressed to find better value for money in the "big" engine stakes. No blowers, intercoolers, turbos, plumbing or headaches here. The toughest parts in an engine swap that ends up looking like a stock LS1 and in fact is physically identical in all dimensions so fits straight in anywhere you had an LS1 or LS2. With a 2750 rpm torque figure of 468 ft.lbs you can forget about needing stiffer diff ratios or hi stall torque converters. Both the Piledriver 440 and the fantastic Sledgehammer 427 are both also available in components only packages for those wishing to assemble and build their own versions. A fully prepped LS7 block is $5500.00, 427 crank kits start at $3100.00, 440 crank kits with the best parts are $4500.00, GM Performance parts heads fully prepped for the 427 are $3500.00 including the special offset intake rocker arms required. The CNC ported 440ci versions of these heads are $5000.00 fully prepared. The matching intake manifold, fuel rails injectors and billet 90mm throttle body induction package is $4500.00 to suit the 427ci Sledgehammer. The same induction package for the Piledriver 440ci engine with fully port matched intake runners to suit the CNC ported heads and our custom billet 95mm throttle body is $6500.00 Our matching camshafts are only $550.00 You have a choice of over 50 grinds. Newest cam profiles...LS1 LSCH-928   228 in  236 exh @.050” lift .551”in .551”ex 114 degree LC             LSCH-936   236 in  246 exh @.050” lift .551”in .551”ex 114 degree LC LSCH-945   245 in  257 exh @.050” lift .560”in .560”ex 114 degree LC LSCH-955   255 in  264 exh @.050” lift .560”in .560”ex 114 degree LC LSCH-961   261 in  268 exh @.050” lift .600”in .600”ex 115 degree LC LSCH-968   266 in  275 exh @.050” lift .600”in .600”ex 114 degree LC   Note: All our LS1 camshafts have now come down in price! They are $550.00 each Our matching conical valve spring sets are $330.00 and chrome moly retainers...$120.00 Want a full list of our full range of cam profiles? Go to http://www.comeracing.com/products/cams/     7:14:03 AM

	Sunday, 23 March 2008

427ci LS1 Sledgehammer   Is your 5.7 LS1 getting tired? We have an alternative you may find hard to resist...our 427ci (7 litre) outright long motor with 605 bhp and 583 ft.lbs torque. There are no inflation  problems here either, our prices are DROPPING. This long engine will cost you only $18,000 assembled. you will use the oil pan, coil packs and other external bolt on ancillaries off your original LS1 engine to fully complete the engine. It is is physically identical to your LS1/LS2 in all dimensions so drops straight in to all model Commodores from '99-2008. Need us to dyno run in the engine and otimimise software tuning so all you need to do is drop it in and go drive?..add $2000.00 This is a bargain in anyones language. You can also buy this engine UNASSEMBLED which includes a brand new fully prepared LS7 GM aluminium block, our complete 427ci Stroker kit with Wiseco or Diamond Racing forged pistons, 4340 steel "I" beam rods and our proven nodular 4.00" stroke crank all fully balanced with new GM crank angle sensor fitted and moly rings with rod and main bearings supplied. A new Powerbond keyed balancer, brand new GM L92 big port cylinder heads, fully prepared with our special conical valve springs, full valve job, chrome moly retainers, new pushrods, COME LSCH-936 hydraulic roller camshaft (specifically developed for this combination), new roller lifters, new timing set, new blueprinted oil pump, timing case cover with cam angle sensor, LS7 valley cover plate, full GM gasket set and head bolts, new L92 big port GM intake manifold with fuel rails and injectors, new COME Racing billet alloy 90mm Throttle body. All this ready to assemble for only...$17,000...These offers are limited and won't last forever. The incredible power and torque of these engines as well as great daily driveability is something one needs to really experience to appreciate. Peak power is made at no more than 5750 rpm with peak torque at 4750 rpm. Don't look only at the peak numbers. As we keep drumming into your heads, it's the torque curve that makes the car accelerate and be driveable. These monsters have over 450ft.lbs torque as low as 2750 rpm. Tuned correctly and driven correctly they can also be incredibly fuel efficient in most conditions. There are many so called experts offering big power LS1 based combinations but no one will give you this torque curve, reliability at these prices...no one! 6:48:45 AM

	Saturday, 9 February 2008

Holden Stroker kits NEW! 396ci Holden Stroker kits  Build the biggest possible Holden stroker using your late model cast iron GMH 304 block. Our new 396ci stroker kit is a very limited offer item as we made very few in our first production run due to extensive testing to ensure reliability. The torque produced is amazing and with the correct choice of unlimited inductions fantastic street/strip results are easily achieved. The introductory batch of 396 Stroker kits is now available and includes a nodular iron 8 counterweight, 3.8750" stroke version crank based on our super strong 383 nodular cast iron crank. We've made a custom length 5.850" forged 4340 steel "I" beam con rod with bushed small ends for fully floating Diamond Racing forged 10:1 compression pistons. Kit is fully balanced internally and includes Diamond Racing moly rings, King rod and main bearings all for an introductory...$3300.00 ECOTEC or VN-VR V6 4.2 Stroker kits...BOOST application kits with the absolute strongest parts available anywhere for the Holden V6 engines. These balanced kits feature our 4340 steel billet stroker cranks, our 4340 steel "H" beam rods with ARP2000 series bolts and either Wiseco or Diamond Racing custom forged pistons, moly rings, rod and main bearings all for $5500.00 (same kit with cast crank for $4000.00) Call us on (03)9571-4204 to order or for information regarding any of our products. Or, email to come@comeracing.com. Trade or wholesale enquiries to workshop@comeracing.com   10:50:41 AM

	Saturday, 1 December 2007

Twin Throttle Body Ecotec intake Ecotec V6 manifold plenum To compliment the full range of 4.2 litre stroker kits, engines, cylinder heads and camshafts we manufacture for the popular Holden Ecotec V6's...announcing the arrival of our Twin Throttle Body intake plenum assembly for the Ecotec engine. This plenum is a direct replacement for the original top plenum incorporating provision for all factory sensors, throttle cable, fuel rails, intake piping. It is a very quick and easy bolt on to the original factory manifold base. Fitting time is less than one hour and the results are incredible even on stock or mildly modified 3.8 litre engines. Our intake plenum features a billet alloy dual 58mm throttle body, increased plenum volume with a beautifully designed zero restriction inlet flange mating precisely to the plenum housing itself. Also included is a very efficient intake snorkel which bolts directly to the billet throttle body and is designed for maximum air flow potential and to hook up to stock intake piping to the production or any aftermarket air box systems. This complete plenum assembly with billet throttle body, intake snorkel, accelerator cable bracket is $1750.00 making it a fantastic value for money easy bolt on. The results even with stock engines is over 10% torque gains right through the rpm range with more significant gains on modified engines, strokers and boost applications. Unlimited possibilities abound and finally the Ecotec engine is allowed to make power to its full potential. Holden V6 Ecotec crate engines 1) 4.2 litre Ecotec stroker long motor...230+kw normally aspirated long motors available outright. These include our new Twin Throttle body intake, fully ported ST-3 heads and balanced blueprinted short motor...$8500.00 outright. The same engine including dyno run in and software tuning optimised is $9900.00 The same engine UNASSEMBLED for the do it yourselfer is $7500.00 NOTE: These engines do not include bolt on ancillaries like alternators, starter motors etc. Your original stock engine ancillaries will bolt right on. 2) 4.2 litre Ecotec BOOST stroker long motor...these long motors are our most popular Ecotec engine by far. They are fitted with our best boost stroker bottom end with low compression boost forged pistons, "H" beam rods and your choice of nodular cast iron crank (up to 20psi boost) or our billet 4340 steel crank for unlimited or endurance applications. They have the same ST3 fully ported heads, "O" ringed block decks, copper head gaskets and fully optimised cam profile from our range to best suit your exact application. This long motor outright less ancillaries but including our new Twin Throttle Body intake is...$10,500.00. The same engine including dyno run in normally aspirated only, so it has some run time on it before boost setups are fitted and tuned, is $11,500.00 The same engine UNASSEMBLED is $9500.00 NOTE: No ancillaries as per the above # 1 engine are included. Add...$1000.00 to any of the above prices for the inclusion of our billet steel crank to replace the cast crank. A full range of 4.2 stroker engines are also available for the Series II VN-VR V6 engines. These are usually only available on an exchange basis although some applications can be supplied outright. Just let us know what you need and we can price it for you. For those wishing to build their own engines ask us for our literature on our full range of Holden V6 stroker kits (rotating crank assemblies), cylinder heads and camshafts. Call us now for information regarding any of our products on (03)9571-4204 or email come@comeracing.com For genuine trade customers we have current special pricing on all our product lines...email us at workshop@comeracing.com with your full name and contact details including ABN # to receive our wholesale pricing. Or call us during business hours on (03)9571-9605 8:00:53 AM

	Thursday, 15 November 2007

427ci (7 litre) COME Racing alloy engines 427ci Holden V8 replacement Our hand crafted all alloy 427ci Holden replacement engines are now steadily shipping. You have a unique opportunity to own this one of a kind engine for street applications in Hot Rods, kit cars, earlier Holden model restorations right up to late model Commodores. Available in carb or EFI configuartion turn key dyno run in engines making your choice of power from 480bhp to 550bhp on pump 98 octane fuels. At $25,000 outright this is the best performance engine value today with the high machining cost of prepping a factory used block and still coming up significantly short in the engine capacity stakes. Not to mention the fact that these hand built engines feature all the top race developed attributes only available in a hand built and crafted "custom" made engine. We of course also offer these engines in unassembled form, in parts only form from the beautiful work of art alloy block, to our latest 2007 series alloy heads, full billet steel crank rotating assemblies and hydraulic roller camshafts designed and built in house. No other Australian performance company can provide a "whole" engine like this. Many and varied optional power and torque curves are available to suit your real application and vehicle. NOW AVAILABLE, our long awaited Ecotec V6 Twin Throttle Body intake plenum assembly. These are $1750.00 delivered (in Australia) and represent incredible torque as well as peak power gains over the broadest rpm range imaginable. Whether bolted onto a stock 3.8 with improved exhaust or fully built 3.8 or 4.2 stroker, you will gain excellent results with this bolt on manifold plenum. Ideal also for boost engines where traditionally airflow restrictions have required much more expensive custom built intakes which frankly are untested and not scientifically designed like ours. Call us on (03)9571-4204 or email come@comeracing.com for more details. 7:58:43 AM

	Thursday, 26 April 2007

Holden Stroker Kits and cranks   Highest quality, lower prices! The COME Racing Holden V8 and V6 stroker cranks and kits are the most popular in Australia by a huge margin. With great strides in production efficiencies we are now offering our cranks and kits at hugely discounted prices...PERMANENTLY. There is now no excuse for rebuilding or modifying your Holden V8 without stroking it to a 355ci or 383ci capacity. All COME cranks are fully machined on our Berco production crank grinders to maximise accuracy of journal sizes and perfect indexing to ensure journals are exactly 90 degrees apart for maximum engine smoothness and power output. You do have alternatives with other cranks on the market, some at even lower prices than ours. If you want the best quality and strongest cranks on the market and at the best prices you now have no need to go by price alone. There is also no need to compromise on buying a cheaper kit with lower power potential pistons or other such components so you cannot upgrade power safely a little down the track when you get greedy for more. All our kits for street/strip applications feature 4340 grade steel connecting rods with ARP bolts and the toughest performance pistons in the industry. 383ci Strokers...fact and fiction... Our competitors would have you believe that Holden 383 stroker engines..... Wear out more quickly...won't have high rpm potential...won't make more power than a 355...wear out cylinder bores due to higher piston side loads...are much more expensive to build...will blow up more easily...will use more fuel...amongst a host of other lame excuses as to why you should buy their 355ci stroker kits and ONLY build a Holden to a maximum of 355ci FACTS...383ci Holden engines easily last as long as any other Holden V8...We have built customers 383's since 1993 some of which have done over 300,000kms and they are still running. We've had at least 100 of these engines back in our shop over the years for rebuilds and absolutely normal wear patterns were obvious. No unusual "side loading" of bores to create rapid wear or split bores. Our powerful engine packages like the "Ultimate" or S.S-3 versions with large port cylinder heads and unrestricted intake manifolds make insane power levels and their biggest feature...incredible torque. Well above anything any 355 could ever hope to achieve. They also achieve these power levels at lower rpm levels for more long term reliability and life potential. YES, they have always been MORE expensive to build. Now with our new pricing levels the gap is very marginal. Only slightly more block clearancing is required over that needed for the 355. Particularly with our EFI 383 engines customers report lower fuel consumption than even stock 5 litre engines when driven sensibly. With so much more torque on hand large throttle openings are simply not required to rapidly accelerate the car. This keeps the engine in closed loop mode much longer actually reducing fuel consumption. If you need any more convincing look at our own Torana's 383 race engine...over 500 1/4 mile passes making over 850 bhp and the crank is still the same one from way back in 1996. Look at Darren Parker's VP SS Commodore reliability results shown in a recent weblog entry below (scroll down for details). Finally look at Eddie Tassone's world record holding twin turbo 383 Holden V8 with over 1890rwhp, 8.1 second 1/4 mile times @ 178 mph. Ask Eddie what he thinks about COME components and particularly our Holden 383 cranks. NONE of these race 383's doing well over 7000 rpm has EVER "blown up". TALK IS CHEAP...FACTS SPEAK FOR THEMSELVES.   Call us Monday to Friday 8.30am to 5.30pm on (03)9571-4204 or email come@comeracing.com Trade customers or urgent enquiries to workshop@comeracing.com   8:11:31 PM

	Friday, 6 April 2007

Ecotec V6 4.2 litre Blower engine The Ecotec Holden V6 has come a long way. With our development of a full range of performance parts for these engines there are new limits to their capabilities. The engine shown above started as one of our off the shelf outright crate motors to suit boost applications. This engine is sold as a long motor outright for $10,500.00 fully dyno run in, in normally aspirated form ready to receive whichever form of boost setup you prefer, blower or turbo. This particular customer supplied us with a very large (too large) Vortec blower and full kit including intercooler, blow off valve, injectors, fuel pressure regulator, pulleys etc. to complete the blower installation. Unfortunately the regulator was faulty, the lower pulley did not fit the stock balancer and we had to do major fabrications, the top blower pulley was way too small for an engine this size and a new $400.00 version was needed. There were many other small items needing to be done and other pieces fabricated to make this a viable installation. Buyers need to keep these factors in mind when buying a $10,000.00 plus blower kit that is supposed to be a "simple" bolt on. Using the latest Kalmaker Mafless boost software and fitted with our newly developed Twin Throttle Body Ecotec intake manifold plenum this little "midget" engine displacing 256ci (just under 4.3 litres) made 505 BHP @ 5750 rpm and 424 ft.lbs torque @ 4500 rpm Maximum boost at 5750 rpm was 14.5 psi The size of this blower being clearly too large was evident in boost lag below 3500 rpm. In fact we saw 3-4 psi @ 2750 fully loaded at which point the engine made 291 ft.lbs torque. By 4000 rpm the boost was rushing in at 8-10 psi and 415 ft.lbs was registering. At the peak rpm of 5750 peak torque of 461 ft.lbs hit home. Now considering the size of this little engine, pump fuel being used and VERY, VERY conservative tuning this power/torque is pretty astonishing when one looks at the low rpm range. We still feel a smaller blower would have worked better to maximise overall results and reduce the lag that most people associate with turbos. Trust me the blowers if too big are no different. Nevertheless considering the results you could easily shove this little monster into a typical VS Commodore with a set of 3.9:1 diff gears, slicks, optimised exhaust system and say a boost friendly torque converter with about 2800 rpm stall speed and easily run high 10 second 1/4 mile times. Then just drive it home and achieve great fuel economy. The latest "self learn" feature of the Kalmaker software optimises the fuel curve almost itself in no boost cruising situations off the normal dual O2 sensor imputs and keeps the engine clean and efficient at part throttle. Engine specs: COME 4.2 litre stroker crank (nodular iron) 3.700" stroke, custom length "H" beam 4340 steel rods, Wiseco forged 8.2:1 compression forged pistons, fully ported Ecotec cast iron factory cylinder heads which flow over 350 bhp through intake ports, COME CSBR-523 hydraulic roller camshaft, Speed Pro lifters, COME Conical valve springs and chrome moly retainers, single row timing set retaining balance shaft for street smoothness, blueprinted production oil pump, fully prepared block with line honed main tunnels, bored and torque plate honed to +.030" oversize, deck surfaces machined and equalised with "O" ring grooves cut and "O" ring wire fitted, Ridgecrest custom made copper head gaskets fitted. Production rocker arms and pushrods retained. They are very strong pieces and everyone throws them out...how stupid can you be? Use them they are tough pieces. Only the pushrods need replacement if you are going to really "turn" the engine very hard. New COME Twin Throttle Body intake plenum fitted on port matched stock Ecotec intake runner base. Stock PCV breather system eliminated to prevent interraction with boost application. Will need external breather setup via rocker covers to catch can or more elaborate breather system. We are doing deals on all our engine packages and components, particularly for those buying multiple parts at one time to achieve a certain build up. Call us during business hours 8.30am to 5.30pm Monday-Friday on (03)9571-4204 or email come@comeracing.com Trade or urgent enquiries please to workshop@comeracing.com   10:10:58 AM

	Sunday, 25 March 2007

Holden Ecotec V6 manifold test Ecotec V6 manifold development Extensive development and testing over the part 15 months has finally yeilded a great bolt on for Ecotec V6 owners. Fitted to an 8.2:1 compression 4.2 litre Ecotec stroker engine on our engine dyno the facts speak for themselves. With peak power of 241 BHP @5500 rpm with stock intake and throttle body the new COME intake plenum with billet dual 58mm throttle bodies produced 266 BHP @5500 rpm. The best part however was something we were really looking for and that was the awesome torque curve improvement. At 2750 rpm the stock setup made 238 ft.lbs the COME intake had 264 ft.lbs Peak torque for both occurred at 4250 rpm, 260ft.lbs for the stock intake versus 278 ft.lbs for the COME intake. Note, the same stock MAF was fitted for both tests. Tests were conducted within one hour of one another and the atmospheric conditions remained reasonably similar with conditions becoming worse rather than better as the day proceeded. Optimum software tuning was applied to both setups and as we expected with the more efficient new manifold, we cut back on the fuel curve to maximise results. Incidentally, stock VS Ecotec #973 injectors were being employed in this baseline test and had plenty more room before running out of fuel flow needs for this engine. This is the same trend we experience with our V8 Twin Throttle Body intake and the results for that piece are well documented. The Ecotec manifold we have developed will really open up the Ecotec performance potential for all applications including normally aspirated or boost setups. The best part of course is the fact that our intake plenum is a simple bolt on. It bolts on in place of the original plenum on top of the stock intake runner base. The original base is a very effective peice and can easily be ported for maximum effort so there was no point replacing the "good" factory base. The problem all along has been the plenum and throttle body assembly. In fact, bolting one of these new Twin Throttle Body plenums on even a stock Ecotec 3.8 will yeild instant significant power and torque gains. Add a little cam and software upgrade and 50 bhp gains will be easily achieved. We still have a few small items to finalise in the design, primarily an intake snorkel setup, correct linkage on the throttle body to mate with production accelerator cables, some detailed changes to allow additional vacuum ports and finally an alternative PCV valve system which will be more desireable for strokers or boost setups. Basically, the hard work is done and we expect to have the new manifolds available for sale within the next 6 weeks or so. Final price has not been determined yet. We are hoping to offer the manifold plenum, billet throttle body and intake snorkel for around $1700.00 If a price close to this is finally feasible, this bolt on is the biggest Ecotec power versus cost bargain you will ever find. More importantly it will move this engine into a realm not seen before. The manifold will raise the bar for much greater power outputs for the Ecotec V6 no matter if it is built as a stroker, stock 3.8, boost, N2O or normally aspirated. As with our Holden V8 engine packages, we will be offering fully built 4.2 stroker engines already fitted with our new intake as changeover engine packages or available as outright buys in the "crate" engine form so common today. There is really no reason now that our typical 220kw Ecotec 4.2 litre V6 cannot now be available as a 230-240kw engine package in normally aspirated form. We envisage these engines to be sold exchange for around $10,000, fully dyno run in and optimised including the new manifold.     1:50:21 PM

	Monday, 12 March 2007

383 Holden reliability and performance 383 Holden EFI...9.98 E.T @133 mph Darren Parker and his VP SS Commodore ran an excellent 9.98 ET and backed it up with a 9.99 finishing runner up in the recent Summernationals at WSID in Sydney. Just last weekend Darren did it again by winning the West Coast race in Perth. The COME 383 has done almost 500 passes in Darren's Commodore. The engine was freshened a 2nd time late last year and still has one of our nodular cast cranks and Keith Black hyperuetectic piston. On this most recent birthday we decided not to be greedy and change the rods and pistons. 500 passes is a lot of work and we can't complain about "street" type components not giving us incredible value for money. In fact, the cast crank looks like new, has no cracks (after all that work) so it went back in. A new set of COME "H" beam rods and custom Wiseco forged pistons were also fitted to complete the upgrade. This engine is based on our 383 Ultimate EFI Holden but has optional solid roller cam and valvetrain, makes 550 bhp on our engine dyno and crosses the finish line just over 7000 rpm every run. You won't find find too many combinations as effective and reliable as this for a weekend Bracket Racer application or for street strip use with it's normal hydraulic roller valvetrain and pump fuel version putting our over 480 bhp year after year. If you are building a Holden V8 as we've said before, give the 383ci capacity stroker a strong consideration. Everyone immediately opts for the 355ci strokers without realising the incredible benefits of the 383 version. To entice everyone considering which capacity stroker to go for we have the following special deals to consider: 1) 383ci 9:1 compression Stroker kit including our 3.750" nodular cast centre counterweighted crank, "I" beam 4340 steel forged conrods, Keith Black hyperuetectic 9:1 compression pistons (up to 9.5:1), moly rings, rod and main bearings and the whole assembly is fully balanced internally...$2750.00 delivered anywhere in Australia. 2) 383ci 10:1 compression Stroker kit includes everything the above kit has plus features higher compression Keith Black hyperuetectic pistons and your choice of press fit or fully flaoting COME "I" beam con rods. The kit is fully balanced internally...$3000.00 delivered anywhere in Australia. If you are one of those people who must have the best and want either kit to include our latest billet 4340 steel crank just add...$1500.00 to either of the above prices. There are even bigger deals available for purchases of crank kit and any of our other components at the same time. You will really save money if you order crank kit, our EFI Twin Throttle Body intake manifold and cam, lifter, chip combinations and/or our latest 2006 VN style alloy heads. This also takes the guesswork out of combination building and final tuning hassles. Basically, machine your block, put the whole lot together and turn the key. For those not wanting to do the work themselves we have some great fully built engine combinations to satisfy every budget and power need. You also need to consider our all alloy crate motors. Our complete 400ci all aluminium engines are on the shelf ready to deliver. We have carburettored "Street" 400ci alloy engines ready to go for $20,000. These killers make a totally streetable 500 + BHP and 500+ ft.lbs torque...ON PUMP 98 FUEL. EFI versions are also ready to go for $22,000 These engines use the same cranks, rods and Keith Black pistons found in Darren Parkers race winning engine, so you know they will last many many years in street and occassional strip applications with virtually maintenance free hydraulic roller valvetrains.   LS1 crate motors We haven't forgotten the late model Commodore owners either. To make performance upgrades easier we have embarked on a crate motor program for the LS1/LS2 style engines as well. Initially, we will be offering easy upgrades for LS1 5.7 litre owners in the form of 408ci short motors. By retaining your complete LS1 top end and simply adding one of our "brand new" 408ci short motors you instantly have 550+BHP and 550+ft.lbs torque to play with with stock LS1 heads and intake manifold. Our 408 short blocks come completely assembled and blueprinted with our ever popular 4.00" stroke nodular crank, new crank angle sensor, "I" beam 4340 steel full floating con rods, custom Wiseco forged pistons, moly rings, new rod and main beaings with the whole assembly fully balanced internally and all fitted into a brand new GM 6.0 litre alloy block. These short blocks include our now famous COME LS1 camshafts (you have a big choice of grinds) and timing set.  Short block price, outright, delivered in Australia...$8000.00 Add $500.00 for "H" beam conrods. Other combinations will be available soon, including turn key outright engines and long motors. Call or email if you have any specific queries about our latest deals. We are fighting inflation with lower prices on the best quality components in the performance industry. Your support over the last 25 plus years has enabled us to streamline production volumes and costs so we are passing the savings on wherever we can. Call on (03)9571-4204 or email come@comeracing.com Trade customers...email workshop@comeracing.com or phone Sam or Issy on (03)9571-9605   4:39:50 PM

	Saturday, 27 January 2007

427ci COME alloy engine # 1 The first COME Racing all alloy 427ci street, pump fuel engine is going together right now. Got an early Holden, Hot-Rod, Kit car, 4x4, truck, Trike or any project car you want to make absolutely unique while having as much or more power and torque than almost anything available in mass produced crate motors? This is the engine to invest in! The only true hand built all alloy complete V8 engine designed and built right here in Australia. Our block, cylinder heads, intake manifold, camshafts, crankshafts and connecting rods are all designed and built right here to be the most durable, cost effective performance powerplant available in Australia at any price. The beautiful part is the fact that it bolts right into any car originally built with the one and only Holden (Plastic) V8 and is very easily adapted to bolt into virtually any chassis. This complete pump fuel engine in various power levels from 550-600 bhp and well over 550 ft.lbs torque, dyno run in and optimised is $25,000 Compare this to a fully built production engine with similar power. In most cases stroker versions costing a lot more money will be required to match the COME alloy 427. Frankly, you will realistically need a very costly engine buildup with blowers, turbos or N2O to compete with the power to weight potential of our 427 alloy engine. When all is said and done, the asking price of our alloy 427 is more than reasonable if you do your comparison sums accurately.   New Product: We now have available forged 4340 steel "H" beam rods to suit stock stroke Holden Ecotec V6 engines. Many customers have asked for these rods in stock centre to centre length. The pin end bore size is the same as the Supercharged V6 rod with .905" bores. These balanced rod sets are $990.00 We also have available matching low compression blower/turbo pistons as well as high compression versions to suit these rods using a production crankshaft or our soon to be available billet steel stock stroke or stroker cranks. The pistons are custom full race forgings made for us by Wiseco pistons in the U.S.  Piston sets with rings are $1,650.00 in .030" oversize. Incidentally, due to a strong customer response we will be continuing our January 2007 special deals through to the end of February 2007. We appreciate your support and will strive to provide the best components at the best possible prices. Trade enquiries are welcome and we have great deals for the performance and engine shops as well.   New Product # 2 Our ever popular Holden billet 4340 steel 355ci cranks are now ALSO available with Holden V8 con rod journals as well as the popular version with Chev 2.1" rod journals. They are also included in our specials list from last month for the same price as the Chev rod journal version. We also have a full range of rods to suit both versions in both "I" and "H" beam designs in 5.7" centre to centre as well as other lengths.  Call us for details on any of our products, special deals or engine combinations we offer for popular V8 and V6 engines. Call (03)9571-4204 or email come@comeracing.com or for instant urgent response email workshop@comeracing.com     10:19:55 AM

	Friday, 20 October 2006

Holden VN-VR 4.2 litre Stroker engines and components The Holden V6 revolution continues with the earlier VN-VR V6 3.8 litre engines now growing to a healthy 4.2 litres. In addition to the already popular 4.2 litre Ecotec engine strokers for both normally aspirated as well as boost applications, owners of earlier model Holden V6's can now stretch the capacity of any VN Series 11, VP or VR V6 3.8 litre engine to 4.2 litres. The engine shown here is one of many coming out of our shop with basic upgrades like fully ported S.T-3 cylinder heads, a COME billet Streetmaster Hydraulic Roller cam profile (numerous choices based on vehicle type and real customer end use). The engine is fully rebuilt and fitted with our latest brand new nodular iron 3.700" stroke large counterweight crankshaft, forged 4340 "I" beam con rods with heavy duty capscrew rod bolts and Hypertec alloy pistons. This fully assembled, dyno run in and optimised engine is $8800.00 if you supply us your complete VN-VR engine for building. Or we can supply the long motors outright with extra cost depending on actual model required. Of course the price includes full assembly, ultrasonically cleaned and flowed injectors, full engine dyno run in and software optimisation with Twin Table Software supplied. You drop the engine back in the car, fit a fully upgraded exhaust, turn the key and drive with no further tuning required. For the do-it-yourselfers, we offer a full range of fully balanced crank, rod and piston kits. The normally aspirated kit price is $2530.00 including, crank, rods, pistons, rings, rod and main bearings and full balancing of all components. For boost or full race applications we offer the same super strong crank, "H" beam 4340 forged steel con rods and custom made Wiseco low or high compression forged pistons, rings, rod and main bearings also fully balanced for $4000.00 The same component combinations as our Ecotec ones are also available for the earlier model VN-VR V6's where we can supply fully machined and assembled normally aspirated 4.2 litre Stroker Short motors outright for $4500.00 Blower/Turbo 4.2 short motors outright for $6500.00 which include block deck "O" rings and custom made copper head gaskets. All our short motors include a COME billet steel roller camshaft (your choice of grind) timing chain and gear set and new Ecotec harmonic balancer. Match either short block with our fully ported S.T-3 cylinder heads for $1995.00 outright or $1750.00 to do yours and you have a fully optimised combination to suit your exact application. No guessing or trial and error. We've done the research and development for you so you simply assemble and drive. Typical power levels for a totally streetable normally aspirated 4.2 litre VN-VR engine as shown above are over 200kw (270+bhp) and 385nm (285 ft.lbs) torque in a daily driveable engine that still manages much better fuel mileage than a 5 litre Holden V8 but accelerates much quicker. In fact in a typical VN-VR Commodore such an engine will easily run mid to low 14's over the 1/4 miles with stock 3.08:1 diff ratio. Fit some 3.7:1 gears and a small hi stall converter and you have a cheap to build and run 13 second true daily driver. For those of you with earlier Holdens or other possible transplant cars, 4 wheel drives etc. think of the possibilities of fitting a V6 like this instead of the typical V8 swaps. These engines make more grunt than many of the V8's and are smaller, lighter, more compact and in fact more legal to fit in many parts of Australia. The Holden V6 revolution has only just begun. In fact, COME Racing is completing development right now of a dedicated Twin Throttle Body intake manifold to fully complement these new Stroker packages and this will extend the horizons of the V6 frontier enormously. Benefiting not only normally aspirated combinations but equally viable and advantageous for the boosted engines. For further information or answers to questions regarding these or any of our products or services email us at come@comeracing.com or phone us Monday to Friday 8.30am to 5.00pm on (03)9571-4204 8:27:13 PM

Previous Entries

June 2010
Sun	Mon	Tue	Wed	Thu	Fri	Sat
		1	2	3	4	5
6	7	8	9	10	11	12
13	14	15	16	17	18	19
20	21	22	23	24	25	26
27	28	29	30
May   Jul